ArthurMartinElux washing machine wiring diagram service manual error code circuit schematic schema repair instruction guide user manual free pdf download

	Search and download service manual

ArthurMartinElux washing machine wiring diagram

Washing machine circuit diagram

Electrical components – appliance Components of electronic circuit board

1. Circuit board

2. Suppressor

3. Main switch (on programme selector)

4. Door safety interlock

5. 1st level pressure switch

6. Anti-boiling pressure switch

7. Anti-overflow pressure switch (certain models only)

8. Heating element

9. Stator (motor)

10. Overload circuit-breaker (motor)

11. Tachymetric generator (motor)

12. Rotor (motor)

13. Drain pump

14. Pre-wash solenoid valve

15. Washing solenoid valve

16. “Door closed” lamp (certain models only)

17. Drum positioning system (DSP) (top-loaders – certain models only)

DOOR_TY Triac for door safety interlock

DRAIN_TY Triac for drain pump

K1 Heating element relay

K2 Motor relay: clockwise rotation

K3 Motor relay: anti-clockwise rotation

K4 Motor relay: half-range power (certain models only)

MOTOR_TY Motor triac

ON/OFF Main switch (programme selector)

PWELW_TY Triac for pre-wash solenoid valve

Serial interface Asynchronous serial interface

WELV_TY Triac for washing solenoid valve

ArthurMartinElux washing machine wiring diagram

EWM1000 wahing machine circuit board connectors

In case of burning on the main circuit board, check that the problem is not caused by another electrical component (short-circuits, poor insulation, water leakage).

Refer to the figures below in order to identify the component that might have caused the burning according to the position of the burned area.

The circuit board shown below is the version with the greatest number of components: other boards may not feature all these components (relay K4 and buzzer).

ArthurMartinElux washing machine circuit control board component side

Table of alarms error codes EWM1000

Alarm	Description	Possible fault	Action/Machine status	Reset
E00	No alarm
E11	Difficulty in filling during wash phase	Tap closed or water pressure insufficient; Drain hose incorrectly positioned; Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty.	Cycle paused, door closed	Start
E13	Water leakage	Drain hose incorrectly positioned; Water pressure insufficient; Water fill solenoid faulty; Leaks or blockage in pressure switch hydraulic circuit; Pressure switch faulty; Circuit board faulty.	Cycle paused, door closed	Start
E21	Difficulties in draining	Drain hose kinked/blocked/incorrectly positioned; Drain filter clogged or dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; Circuit board faulty; Current leakage from heating element to ground.	Cycle paused	Start
E23	Drain pump triac faulty	Drain pump faulty; Wiring faulty; Circuit board faulty.	Safety drain - Cycle stopped, door open	Selector on “0”
E24	Problems with «sensing» of drain pump triac	Circuit board faulty.	Safety drain – Cycle stopped, door released	Selector on “0”
E33	Incongruence between contact closure of anti- boiling and 1st level of pressure switch	Pressure switch faulty; Current leakage from heating element to ground; Heating element; Wiring faulty; Circuit board faulty.	Safety drain - Cycle stopped, door open	Selector on “0”
E35	Water overflow	Water fill solenoid faulty; Leaks from pressure switch hydraulic circuit; Pressure switch faulty; Wiring faulty; Circuit board faulty.	Cycle blocked, door closed. Safety drain. Drain pump (sequence 5 min. ON - 5 min. OFF)	Selector on “0”
E36	«sensing» circuit of anti-boiling pressure switch faulty	Circuit board faulty.	Cycle blocked, door closed	Selector on “0”
E37	«sensing» circuit of 1st level faulty	Circuit board faulty.	Cycle blocked, door closed	Selector on “0”
E39	HV «sensing» circuit of anti-flooding pressure switch faulty	Circuit board faulty.	Cycle blocked, door closed	Selector on “0”
E41	Door open	Door safety interlock faulty; Wiring faulty; Circuit board faulty.	Cycle paused	Start
E42	Problems with aperture of door	Door safety interlock faulty; Wiring faulty; Circuit board faulty	Cycle paused	Start or Selector on “0”
E43	Power triac on door interlock faulty	Door safety interlock faulty; Wiring faulty; Circuit board faulty.	Safety drain, door released	Selector on “0”
E44	Door interlock «sensing» faulty	Circuit board faulty.	Safety drain, door released	Selector on “0”
E45	«sensing» on door interlock triac faulty	Circuit board faulty.	Safety drain, door released	Selector on “0”
E51	Motor power triac short-circuited	Circuit board faulty; Current leakage from motor or wiring.	Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)	Selector on “0”
E52	No signal from motor tachimetric generator	Motor faulty; Wiring faulty; Circuit board faulty.	Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)	Selector on “0”
E53	«sensing» circuit on motor triac faulty	Circuit board faulty.	Cycle blocked	Selector on “0”

E54	Motor relay contacts sticking	Circuit board faulty; Current leakage from motor or wiring.	Cycle blocked, door closed (after 5 attempts in diagnostics or immediate during selection)	Selector on “0”
E61	Insufficient heating during washing	NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty.	Heating phase skipped	---
E62	Overheating during washing	NTC sensor faulty; Heating element faulty; Wiring faulty; Circuit board faulty.	Safety drain (with cooling water fill) - Stop with door open	Selector on “0”
E66	Power relay for heating element faulty	Circuit board faulty; Current leakage from heating element or wiring to ground.	Safety drain (with cooling water fill) - Stop with door open	Selector on “0”
E71	NTC washing sensor faulty	NTC sensor faulty; Wiring faulty; Circuit board faulty.	Heating phase skipped	---
E82	Error in reset position of selector	Circuit board faulty.	Cycle cancelled	Selector on “0”
E83	Error in reading selector position	Configuration data incorrect; Circuit board faulty.	During the cycle continues normally, switches off completely during selection	---
E93	Incorrect machine configuration	Configuration data incorrect; Circuit board faulty.	Appliance blocked	Selector on “0”
E94	Incorrect washing cycle configuration	Configuration data incorrect; Circuit board faulty.	Appliance blocked	Selector on “0”
E95	Communications error between microprocessor and EEPROM	Circuit board faulty.	Appliance blocked	Selector on “0”
E96	Incongruence between hardware version and configuration.	Configuration data incorrect; Circuit board faulty.	Appliance blocked	Selector on “0”
E97	Incongruence between programme selector and cycle configuration	Configuration data incorrect; Circuit board faulty.	Appliance blocked	Selector on “0”
EB1	Power supply frequency of appliance incorrect	Mains power supply problems (incorrect / interference); Circuit board faulty.	Cycle blocked until normal power supply conditions are restored	Selector on “0”
EB2	Voltage too high	Mains power supply problems (incorrect / interference); Circuit board faulty.	Cycle blocked until normal power supply conditions are restored	Selector on “0”
EB3	Voltage too low	Mains power supply problems (incorrect / interference); Circuit board faulty.	Cycle blocked until normal power supply conditions are restored	Selector on “0”

Notes concerning certain alarm codes

Configuration alarms E93-E96: If these alarms are generated (when the appliance is switched on), operation of the appliance is blocked and all the LEDs light. The diagnostics procedure cannot be accessed; the only option is to switch the appliance OFF (by turning the selector to position “0”).
Configuration alarm E94: For this alarm code, only the family for alarm “9” is displayed; the diagnostics procedure cannot be accessed, and the “rapid alarm display” function cannot be used.
Alarms EB1-EB2-EB3: In the event of problems with the mains power supply, the appliance remains in alarm mode until the mains frequency or voltage are restored to the correct value or the appliance is switched off (by turning the programme selector to “0”). The family of alarm “B” is displayed; the diagnostics procedure cannot be accessed, and the “rapid alarm display” function cannot be used. The complete alarm code can be read only when the abnormal situation has ceased.
Alarms E51- E52: During the diagnostics test, all the alarms are displayed. Normally, when the programme selector is turned from one test phase to another, the appliance exits the alarm condition and performs the phase selected. This does not take place in the case of alarms E51 (power triac on motor short-circuited) and E52 (no signal from the tachymetric generator on the motor): in these cases, the only option to exit the alarm condition is to switch the appliance OFF by turning the selector to position “0” (reset).

PNC_ELC	Platform	Pub	Model	BrandName	ProdDate
91479121700	EWM1000	599362863	AWF1010	ArthurMartinElux	20040220
91479115500	EWM1000	599356983	AWF1015	ArthurMartinElux	20030228
91479121900	EWM1000	599362866	AWF1020	ArthurMartinElux	20040220
91421104600	EWM1000	599368051	AWF1040	ArthurMartinElux	20041231
91421104602	EWM1000	599371730	AWF1040	ArthurMartinElux	20050708
91421111800	EWM1000	599375810	AWF1040	ArthurMartinElux	20060217
91421111801	EWM1000	599381967	AWF1040	ArthurMartinElux	20060811
91421111802	EWM1000	599388946	AWF1040	ArthurMartinElux	20070518
91452200200	EWM1000	599381400	AWF1075	ArthurMartinElux	20060714
91452200201	EWM1000	599383749	AWF1075	ArthurMartinElux	20061027
91479121800	EWM1000	599362865	AWF1115	ArthurMartinElux	20040220
91421511200	EWM1000	599371915	AWF1140	ArthurMartinElux	20050708
91421520501	EWM1000	599377213	AWF1140	ArthurMartinElux	20060317
91421520502	EWM1000	599382128	AWF1140	ArthurMartinElux	20060825
91421520503	EWM1000	599704362	AWF1140	ArthurMartinElux	20071123
91479115600	EWM1000	599356838	AWF1215	ArthurMartinElux	20030221
91479122000	EWM1000	599362869	AWF1220	ArthurMartinElux	20040220
91452200000	EWM1000	599378068	AWF1273	ArthurMartinElux	20060421
91452200001	EWM1000	599383747	AWF1273	ArthurMartinElux	20061027
91479122100	EWM1000	599362870	AWF1420	ArthurMartinElux	20040220
91422510200	EWM1000	599371918	AWF1440	ArthurMartinElux	20050708
91422520201	EWM1000	599377220	AWF1440	ArthurMartinElux	20060317
91422520202	EWM1000	599382370	AWF1440	ArthurMartinElux	20060830
91422520203	EWM1000	599385290	AWF1440	ArthurMartinElux	20060908
91422520500	EWM1000	599383391	AWF1442	ArthurMartinElux	20060728
91422520501	EWM1000	599384817	AWF1442	ArthurMartinElux	20060908
91479110800	EWM1000	599351882	AWF910	ArthurMartinElux	20020411
91479111900	EWM1000	599353515	AWF910C	ArthurMartinElux	20020711
91479115400	EWM1000	599356981	AWF915	ArthurMartinElux	20030228
91479119000	EWM1000	599360158	AWF915C	ArthurMartinElux	20030801
91421104300	EWM1000	599368046	AWF916	ArthurMartinElux	20041231
91421104500	EWM1000	599368050	AWF940	ArthurMartinElux	20041231
91421104502	EWM1000	599371727	AWF940	ArthurMartinElux	20050708


	ArthurMartinElux washing machine schematic diagram error codes fault service manual circuit diagram wiring schema repair instruction guide user manual free pdf download. ArthurMartinElux Service Handbuch Schaltungen Reparaturanleitung Bedienungsanleitungen kostenlos pdf download. ArthurMartinElux Schéma service manual schéma zapojení schémat oprava návod k obsluze návod k použití free pdf ke stažení. ArthurMartinElux Schéma de principe de service manuel Schéma câblage schéma réparation instruction notice manuel téléchargement gratuit pdf. ArthurMartinElux Diagrama esquemático serviço manual do circuito diagrama de fiação esquema reparação instrução guia manual do usuário livre PDF Download. ArthurMartinElux Schema di servizio manuale circuito schema elettrico schema di riparazione di istruzioni guida manuale pdf gratuito scaricare. ArthurMartinElux schemat instrukcja obsługi Schemat okablowania Schemat naprawa instrukcja instrukcja obsługi free pdf pobierz. ArthurMartinElux şeması servis manuel devre şeması kablolama şeması onarım talimat kılavuzu kullanım kılavuzu ücretsiz pdf indir. ArthurMartinElux Schema service manual schema bedrading schema reparatie gebruiksaanwijzing handleiding gratis pdf te downloaden. ArthurMartinElux schematică diagrame de service manualul de circuit diagrama de conexiuni Schema de reparatii de instructiuni Manual de utilizare pe gratis download pdf.

	1. PURPOSE OF THIS SERVICE MANUAL The purpose of this Service Manual is to provide Service Engineers, who already have the basic knowledge necessary to repair household washing machines, with information of a general nature regarding the HEC range of washing machines. More detailed information regarding specific models may be found in the Service Notes and Service Manuals (issued separately) for each specific model or functionality. This information covers: Circuit diagrams Exploded views of spare parts Spare parts lists Functions and diagnostics 2. IMPORTANT NOTES Repairs to electrical appliances must be effected only by qualified personnel. Before accessing the components inside the appliance, always remove the plug from the power socket. Where possible, ohmic measurements should be effected rather than direct measurement of voltage and current. Certain metal components inside the appliance may have sharp edges. Care should be taken to avoid cuts or abrasions. Before laying the appliance on the floor, always drain any water by means of the system placed beside the drain filter. Never lay the appliance on its right side (i.e. electronic control unit side); this would cause the water in the detergent dispenser to fall onto electrical components, thus damaging them. After repairing the appliance, always perform the final tests. 3. CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS of this publication. Remember: Safety First. General Guidance An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.