Dansai schematic diagram service manual circuit diagram wiring schema repair instruction guide user manual free pdf download

 

       
       
       
       

 

 

                                                          Search service manual

   
   
   

Brand Name      Model      Chassis

V Dansai CTV1410 Orion chassis with STR5412 in PSU PCB marked MCS M3 94V-0 LOPTx 101-214017, Ics STR5412, KA2914A, MN15245KWC, KA2154

TV Dansai CTV1477 Binatone 01/9014 Boots CTV1414R Matsui 1450

TV Dansai CTV1477 Binatone 01/9014 Boots CTV1414R Matsui 1450 Saisho CT147R

TV Dansai CTV1481R Indiana 100

TV Dansai CTV1481R/T Indiana 100

TV Dansai CTV2004T Indiana 100

TV Dansai CTV2004T Indiana 100

TV Dansai TA11401 Decca 141 Solarvox Nikkai TLG99

TV Dansai TA11401 Decca 141 Solarvox Nikkai TLG99

TV Dansai TAT1051 Indiana 100

TV Dansai TAT1051 Indiana 100

 

 

     
   Dansai schematic diagram service manual circuit diagram wiring schema repair instruction guide user manual free pdf download. Dansai Service Handbuch Schaltungen Reparaturanleitung Bedienungsanleitungen kostenlos pdf download. Dansai Schéma service manual schéma zapojení schémat oprava návod k obsluze návod k použití free pdf ke stažení. Dansai Schéma de principe de service manuel Schéma câblage schéma réparation instruction notice manuel téléchargement gratuit pdf. Dansai Diagrama esquemático serviço manual do circuito diagrama de fiação esquema reparação instrução guia manual do usuário livre PDF Download. Dansai Schema di servizio manuale circuito schema elettrico schema di riparazione di istruzioni guida manuale pdf gratuito scaricare.Dansai  schemat instrukcja obsługi Schemat okablowania Schemat naprawa instrukcja instrukcja obsługi free pdf pobierz. Dansai şeması servis manuel devre şeması kablolama şeması onarım talimat kılavuzu kullanım kılavuzu ücretsiz pdf indir. Dansai Schema service manual schema bedrading schema reparatie gebruiksaanwijzing handleiding gratis pdf te downloaden. Dansai schematică diagrame de service manualul de circuit diagrama de conexiuni Schema de reparatii de instructiuni Manual de utilizare pe gratis download pdf.  
     
  CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS of this publication. Remember: Safety First.

General Guidance An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line.

Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

General Servicing Precautions


1. Always unplug the receiver AC power cord from the AC power
source before;


a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
 

2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
 

3. Do not spray chemicals on or near this receiver or any of its
assemblies.
 

4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
 

5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
 

6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
 

7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
 

8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.

 

 

 
Copyright © 2007 Tehnomagazin.com
Terms & Conditions                                        Privacy Policy                                                Impressum